They are making several good pointers on A Step-by-Step Guide to Installing a Bathtub in general in the content on the next paragraphs.
Mounting a bath tub isn't specifically brain surgery, yet it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a new one is likewise a reasonably hard task. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open up a wall to eliminate the old tub and position the new bathtub, the job is much harder. In either situation, the task is within a residence handyman's skills, although you will certainly need a helper to leave the old tub and also embeded in the new one. Make sure you have certified on your own for the job as well as are comfortable trying it. Instead of employing a specialist to take control of a halfway-completed job, it is better to take into consideration employing one before you start. Opportunities are you may need an expert plumber to make tube links.
This article will assist you mount a brand-new bathtub in your washroom if you have actually already purchased a new bathtub as well as do not require to change the plan of your previous water supply pipes.
Your tools and also product checklist should make up the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you must do is separate the water. After doing so, activate the taps to drain any water staying in the system. The procedure of eliminating the existing taps can be quite bothersome due to the limited accessibility that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a towel ready for the remaining water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this process. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Before proceeding to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin ensuring that the washers are in area in between the faucet and also the sink. Secure the faucet in position with the manufacturer offered backnut. When the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap connectors. The former kind should be linked to the tap finishes first, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Tub
Utilizing both wood boards under its feet, position the tub in the needed position. The wooden boards are practical in equally spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four little factors.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and also changing the feet on the bathtub until the spirit level checks out degree.
To set up taps, fit the bottom of the outermost versatile faucet adapter to the proper supply pipe by making a compression join; after that do the very same for the other faucet.
Turn on the water system and check all joints and also new pipework for leaks as well as tighten them if necessary. Fill the tub as well as additionally check the overflow electrical outlet as well as the typical electrical outlet for leaks.
Lastly, repair the bath paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the bathtub ought to wait till the tub has actually been utilized at least when as this will resolve it into its last position.
Preparing for the Setup
Firstly, the sustaining structure supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps device to stop pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of both taps making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its last position.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a rigid seal, causing the water to penetrate the wall in between the bathroom and also the tiling, bring about difficulties with wetness as well as possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your components and also fittings. They are marketed in tubes and also cartridges, as well as can securing voids as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill the bathtub with water prior to securing, to enable the movement experienced when the tub remains in use. The sealer can break relatively very early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently readily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been made aware of that report on Tools You Need to Install a New Bathtub from an acquaintance on another blog. Sharing is good. Who knows, you may just be doing someone a favor. Thank you so much for taking the time to read it.
Tap problems? Reach.